SOLD SOLD SOLD. Myford Super 7 Metric Lathe with Gearbox, Power Cross Feed and a Deep Tray. The lathe,in the main, has been stripped to bare metal, repaint/sprayed in Myford Green, cleaned and oiling all parts for reassembling. I have had this lathe in excess of two years waiting for the right parts to become available. I also decided to make this a Metric lathe and use the newer style handwheels.
- Myford Super Seven
- Myford Super 7 Gearbox Manual Download
- Myford Super 7 Gearbox Manual Pdf
- Myford Super 7 Gearbox Manual Transmission
This was a ML7-R in such an excellent condition I had to upgrade to Full Super 7 status ! The original lathe had a cut off and capstan fitted which was removed and this bed could take a Power Cross Feed(PXF) configuration. This was the first saddle it had seen and it has been shimed correctly and it fitted perfectly ! The bed is not worn at all and has only a few marks, mainly where original equipment was fitted. Obviously a Clutch had to be fitted and then go the whole hog and put on a Gearbox, with a metric conversion kit, Both the Gearbox and PXF have been serviced and new parts changed where necessary,
The Headstock was serviced by Myford Beeston prior to their demise, A new spindle was fitted and the front bronze bearing scrapped to fit along with two new angular bearings, new 60t backgear, new 17/53t backgear cluster, backgear eccentric, front oil cup, wick & spring
Myford Super 7B 3.5 x 19in with gap-bed, backgeared and fitted with a screwcutting gearbox and power cross feed. Mounted on a Myford stand with deep chip tray and leveling blocks. Single-phase motor. Machine No: SK143495. Comes complete with: 3 jaw 4in Pratt Burnerd chuck 4 jaw chuck 9in faceplate & 7in faceplate Chuck backplate Catchplate. Myford Part No 80024. We shall call this simply H32. Esso Febis K68 Oil – a heavier “sticky” oil for use in the gearbox, on gears and preferably on slide-ways. We shall call this K68. N e r s s a t n d e-l y n n 2s d. E s n 3t-t e t y t t s f.
ALL the following parts are NEW genuine Myford Parts .Headguard speed plate, Gearbox speed and screwcutting charts. The Top Slide, Chrome Handle and Micrometer. The Cross Slide, Chrome Handle and Micrometer. Tailstock Metric barrel and handwheel. Apron handwheel. Leadscrew Metric handwheel and pointer. Thread Dial Indicator, Saddle Wiper and Housing. Oil nipples. Quick Change Toolpost and 6 holders. Both belts.
Now go and check the cost of these parts and you will fully understand the price. If you could buy this new today I do not think this offering would be far off looking the same.
Motor options. 1) New single phase 1HP motor with Dewhurst forward-on/off -reverse switch(Right) OR 2) New three phase 1HP motor with new 1HP inverter and choice of a new forward-on/off – reverse switch(Left). Very easy to wire with instructions and assistance. I am happy to wire for you upon receiving your specification and a few days notice before collection.
It comes with 3 Jaw Chuck with inside and outside jaws and key and Drill Chuck with a key. New Original Tailor made lathe cover, complete with the Myford logo, manufactured in polythene, which will help protect the lathe when not in use. Part Number 11574.
A deep drip tray with raising blocks resprayed in Myford Green are also supplied. This configuration is intended for a bench setup. I can however supply a cabinet at a very advantageous price, if required.
Super 7 Manual and Gearbox Manuals in A4
Motor disconnected for transporting. Can breakdown further for transporting and can help load vehicle
If you do not require the Tray and raising blocks, price can be reduced by £125.00
I will consider a part exchange of a ML7 or ML7-R or Super7 ONLY. I will need some pictures and price you are looking for.
Viewing of all of my lathes is most welcomed I have been refurbishing Myford ML7 & Super 7 lathes for 6 years and as i’m retired I spend a lot of time getting it correctly set up and a superb paint finish.
07811-386212 for appointment or email to [email protected]
Strictly CASH ON COLLECTION or cleared cheque ONLY from Milton Keynes.
NOW SHOWING ON EBAY.CO.UK
See My Other Myford Lathes and Parts here and on ebay
Click on image to expand(BIG). Back arrow to return here.
For further information, complete this form.
SOLD SOLD SOLD. Myford Super 7 Long Bed with Gearbox. SKL57793. The lathe has been mainly stripped to bare metal, repaint sprayed in Myford Green, cleaned and oiling all parts for reassembling.
The Saddle, The Cross and Top slides all are tight and move smoothly. The Bed has very few marks for its age, and is in excellent condition. Only .0005″ over the 1st half of the bed and a further .0004″ over the next !!!!. That is .0009″ over 38 inches. Quite remarkable for its age. I do try to get the best.
The headstock spindle, bearings and thread on the nose are all ok. All Gears, including backgears, are smooth and have no teeth missing.
All Oil nipples have been replaced. New Top Slide & Cross Slide Chrome Handles and Micrometers from Myford. Gearbox has been serviced and a New Gearbox Screwcutting Chart fitted. All Carriage and slides gib screws & nuts replaced along with Saddle Felt Wiper and Housing. Knobs and the majority of screws, nuts and bolts replaced. Both Belts have been renewed. New Apron Handwheel(now rare), Original Tailstock Handle and Leadscrew Handle inc Pointer. Thread Dial Indicator Fitted.
Minerva t2000 manual pdf. Tyco Minerva MX T2000R Marine Full Function Repeater Panel. MINERVA MX is a comprehensive range of fire controllers designed and built to BSEN ISO9001/2 and EN54. An advanced proven microprocessor-based system, MINERVA MX provides conventional and digital addressable detection for new, refurbished and refitted detection systems.
Comes with 3 Jaw Chuck with inside and outside jaws and New Drill Chuck, both with keys. New Original Tailor made Lathe Cover, complete with the Myford logo, manufactured in polythene, which will help protect the lathe when not in use. Part Number 13602. Original Super 7 Manual and Gearbox Manual. Almost new modern single phase 3/4HP motor wired to a Dewhurst forward-on/off -reverse switch for bench mounting. I do not have a Long Bed deep tray or cabinet, but i will supply raising blocks sprayed in Myford Green.
Motor disconnected for transporting. Can breakdown further for transporting and can help load vehicle
Myford Super Seven
![Myford Super 7 Gearbox Manual Myford Super 7 Gearbox Manual](https://bookbarking.com/myford-super-gearbox-manual-book.jpg)
To upgrade this Lathe to Metric, the following parts would be fitted and replace the Imperial parts. Topslide Feedscrew/Nut & Micrometer. Crossslide Feedscrew/Nut & Micrometer.Tailstock Barrel and Leadscrew Handle. All these parts would be Genuine and supplied by Myford. I would supply a used Myford Metric Conversion Gears & Banjo, replacing the existing Imperial Set. All this for only an additional £225.00
Viewing of all of my lathes is most welcomed I have been refurbishing Myford ML7 & Super 7 lathes for 6 years and as i’m retired I spend a lot of time getting it correctly set up and a superb paint finish.
07811-386212 for appointment or email to [email protected]
Strictly CASH ON COLLECTION or cleared cheque ONLY from Milton Keynes.
Myford Super 7 Gearbox Manual Download
NOW SHOWING ON EBAY.CO.UK
See My Other Myford Lathes and Parts here and on ebay
Myford Super 7 Gearbox Manual Pdf
Click on image to expand(BIG). Back arrow to return here
Myford Super 7 Gearbox Manual Transmission
For further information, complete this form.